a. First, to rule it out as the cause for the fan's problem (e.g. the fan will get loose because of the collision, therefore, it will make noises). You may check whether the fan can work normally without playing any videos or music when the projector is on.
b.There is the heat source of the LED lights inside the projector and it needs the fan to cool down. The noise of the fan should be within 50DB on the date of manufacture.
c.Customers are not allowed to replace the fan by themselves.
a. The use and preservation humidity of the projector should be controlled between 40% and 80%. If the air humidity is not within the range, you may take some measures to reduce the humidity like put a dehumidifier in the room;
b.Pre-heating before turning the projector on can help get rid of the condensation, or you may put the projector in a dry environment for 48 hours.
a. First, make sure the dirt or fingerprints were not stuck to the surface of the lens when the consumers were unpacking the product or during the use of the projector. The dirt on the surface of the lens can be wiped off by cleaning cloth and it will not be a matter to the use.
b.If the dirt or fingerprints are within the lens, the consumers may not be able to deal with this problem by themselves.
c.Before the products leave the factory, the QA technician will carefully check the cleanliness inside the lens; while there is a missing rate of inspection or the accidental drop of the machine may also cause a dirty lens.
a. First, to rule it out as the cause of the speakers' problem. You may switch to other signal sources like HDMI, flash drive play to decide whether it's the problem of the speakers;
b.If other signal sources are normal, you may check if the fire stick has been misused or broken down;
c.VGA signal does not support audio transmission. VGA is a video transmission standard and can only transmit videos or images;
d.It is highly possible that the mainboard of the projector has broken down if the external loudspeakers fail to synchronize with sounds.
The shadow can be a display error caused by oil dirt or other dust.
The burn-in is typical and usually caused by the malfunction of the cooling system. It is suggested that the projector shall not be used under a high-temperature environment and please do not block the air inlet/outlet.
a. The LED lights have thermal protection settings and it will turn off automatically when the temperature is too high. Usually, this problem is caused by the malfunction of the cooling system.
b.Please check if the fan is working normally. Do not block the air inlet/outlet and do not use the projector under a high-temperature environment.
The LCD projector is not dust-proof and the dust can get into the projector through the air inlet or the dust is inside the projector already so that the projection shadow occurs.
Vibration or shock may get the structure stuck.
a. If the LED lights touch the foreign matter, the short circuit may occur and cause malfunction of the lights.
b.The iron will be used during the lights replacement process and the positive and negative of the lights are welded on the power board. Therefore, it is too dangerous for users to replace the lights by themselves.
When the computer is connected with the projector, you need to set the "projection display method" and usually, it is recommended to choose "copy".
a. Projection imaging is a technology that functioned by 10 lenses inside the body. The position or the shape of any lens and the focal length may affect its image shaping, which displays particularly obvious on machines with a resolution of 480/720 pixels.
b. The clarity of products will be through 100% quality inspection to make sure they all meet our specs. Customers can optimize the product by following below if they cannot adjust it properly：
1. Ensure the image is projected in a square, that is to say, the machine should be positioned properly (the left and right side of the screen should be in the same length, so is the up and downside of the screen);
2. Reduce the keystone correction, for it, may change the light path and drift away from the best clear point;
3. Adjust the focal length so that the lens can move from one point to another to refocus. This is to amend the position of the lens that may drift away from being transported or crashed.
a. Make sure the power is on before pressing the startup key;
b. Does the fan work when the machine is on? If it does while there is no image, there may be something wrong with the mainboard or LED/LCD screen, which need to get fixed by the factory;
c. If the machine is with battery, the battery should be checked anyway: Check if the pilot light is on when the adapter is plugged in or compare with other adapters (i.e.mobile phone adapter). This is to check if the original adapter works or not; If not, a new one will be delivered to customers at once; The use of non-original adapters may not be able to meet the power of the projector for playback and charging, resulting in a failure normal startup of the machine. Customers hereby are suggested to use the original one.
a. Confirm the format and capacity of the U-disk (Format: FAT32; 9-32G)
b. DO NOT operate while upgrading
c. DO NOT cut down the electricity while upgrading
d. Please refer to the guide video or manual that is provided. The general guidance is as follows:
1. Customers shall unzip the files and save them into the U-disk (Format: FAT 32; 9-32G) instead of into a folder;
2. Switch on the power and plug in the adapter ( or power cable);
3. Upgrade will be automatically triggered once the power is on (some may need to go to 'settings' - 'local upgrade' to get updated);
4. Power will be switched on automatically once the upgrade is done.
a.Ensure to select the correct signal source, which can be operated by monitor or User Interface.
b.Customers can use other HDMI to test if the problem caused by the cable material or interface fault.
c.There was a problem with the 2.4MacBook output adapter that was 4K and not downward compatible with 1080P when entering the device (such as from HUB, Mini DP to HDMI); Or there's something wrong with the cable(lightning to HDMI) itself.
a.Linux operation system responses slower than Android;
Moreover, Linux buffers data occasionally, which does have impacts as time goes by.
b. If there has some evident pause, customers are suggested to switch the machine off or restore the factory default settings.
a. Take Burger 101 as an example: Theoretically, battery with 5200mAh lasts 1hr & 40mins. However, it may vary from a lower-temperature environment or the place where you set.
b. Ensure if there's something wrong with the battery: Play a movie after the battery is fully charged. It is normal if the battery lasts more than 1hr;
c. Technically, the battery will be charged on and off, meaning the more time it gets charged, the less time it lasts; Customers are suggested to connect an adapter when playing a movie that is more than 2hrs.
a. Active-shutter 3D Glasses are required to use.
b. 3D Glasses in the format of Side By Side, Top Bottom are currently supported; while Frame Packing can be used only through HDMI input that played by blue-ray DVD player
c. Remove those possible lights which may interfere the glasses to receive the signal
a. The format of U-disk is FAT, which maximum supports with 32G.
b. Open the video file information to ensure it is in the correct format; Otherwise, convert it.
PS: There are 2 files when downloading videos by Apple Mac. One of them is available to be played.
Claw hanger in the market usually comes with a size description that complies with all kinds of machines. Customers should purchase the proper one and the machine should be able to claw if they're patient enough.
Clarity of all the products will be through 100% quality inspection to make sure they all meet our specs. Customers can do as follow to get optimized:
1. Ensure the image is projected in a square, that is to say, the machine should be positioned properly (i.e. the left and right side of the screen should be in the same length, so is the up and downside of the screen);
2. Reduce the keystone correction, for it, may change the light path and drift away from the best clear point;
3. Adjust the focal length so that the lens can move from one point to another to refocus. This is to amend the position of the lens which may drift away from being transported or crashed.
The Vankyo projector Leisure 3W does support with the wireless multi-display but not with the wire one, which requires an extra screen stick to receive multi-display.
The recommended minimum distance for projection is: 1.5-2.5meters between the lens and projected images; while the size of images should around 60-80 inches.
No, U-disk upgrade only.
a. Understand the format and capacity of the U-disk (Format: FAT32; 9-32G)b. DO NOT operate the device/cut down the electricity while upgrading. Please refer to the provided guide video or manual.
The general guidance is as follows:
1. Unzip the files when receiving it and save into the U-disk (Format: FAT 32; 9-32G) instead of into a folder;
2. Switch on the power and plug in the adapter ( or power cable);
3. Upgrade will be automatically triggered once the power is on (some may need to go to 'settings' - 'local upgrade' to get updated);
4. Power will be switched on automatically once the upgrade is done.
The available power supply voltage is between 100v - 220v.
Normally a small device comes with 1 speaker while a larger one comes with 2. Details can be referred from the corresponding specification.
There are normally two IR receivers (front&rear) inside the device. Pointing at the device and the images are both available for remote control to receive the signal.
Normally a small device comes with 1 speaker while a larger one comes with 2. Details can be referred from the corresponding specification.
The brightness standard of a projector is presented with ''LM''. 'Lux' may refer to illumination level which normally measured 30cm away from the lens. Normally, 100LM is in accordance with 4500Lux, and 200LM corresponds to 9000Lux.
a. The default refresh rate of our projector is 60Hz which is adjustable.
b. There are differences between framerate and refresh rate. To put it simply, refresh rate functions on the projector while framerate applies to the game graphics card. The fixed refresh rate of the projector is 60Hz which has nothing to do with the graphics card performance. However, the higher the game framerate, the better the graphics card performance.
The power of our device in a small size is about 50W while 150w in large size.
Our projectors currently support USB2.0 rather than USB 3.0.
The maximum capacity comes with 32G.
The angle of keystone correction varies from ±30° to ±50°. You may check from the specification accordingly.
The versatile length of US cable is 1.5m. You may check from the specification accordingly.
a. First of all, the power cable we provide for a smaller device is normally in shape "8“ (see the picture);
b. In addition, the power cord plugs of each country are different, and the power plugs of the same country can be Shared
Our general United States standard HD wire length is 1.5 meters. Details can be referred from the specification of the corresponding machine.
Most remote controls of our company are shareable. Only a few have an extra button for electronic correction. More details can be referred from the corresponding product engineer.
a. Because the APP developer has set copyright restrictions, the video cannot be decoded and transmitted on the same screen.
b. Customers can use the Fire TV Stick or TV Box to play copyrighted apps via HDMI.
a. The projector does not support 5G network. Ensure it is 2.4g network or customers can try to connect it by using mobile hotspot (please refer to the instruction video for connection method)
b. Because of the system response delay, it is suggested that exit the Settings and re-enter it, should the connection be successful.
c. If the WiFi list is not found, it may be the problem of WiFi module, a new one should be replaced for the customer.
d. It is suggested that close to the router to re-test or the customer restore factory Settings to reconnect
A. Youtube APP is a lightweight browser that opens native YouTube videos, and we're a Linux operating system, not as powerful as Android.
B. Due to the reason of 1, APP background maintenance will always do relevant restrictions and filtering; Some video sources have copyright restrictions, which are based on the publisher of the video;
C. Customers can use Fire TV Stick or TV Box to play apps with limited copyright via HDMI
A. The operating system is Linux, which cannot download and install apps like the Android system
B. Customers can use Fire TV Stick or TV Box to play copyrighted apps via HDMI
Comments will be approved before showing up.
